Sealing and protecting Limestone and Travertine tiles

Basic principles of sealing Limestone and Travertine tiles

Understand your surface

Clasic Limestone floor tiles

Are you sure you know your surface?

Are you sure that your surface is Limestone or Travertine? Although this may sound obvious ensuring that you fully understand the type of surface you are dealing with before sealing is vital. If you are in any doubt about the type of wall or floor tiles you have our online identification guide is a helpful place to start. Limestone and Travertine are delicate natural stone materials that have always been a popular method of decoration in kitchens and bathrooms. When used to cover wall and floors they need careful preparation, sealing and ongoing maintenance. Natural stone such as Limestone and Travertine is by nature unsealed. As such all forms of natural stone wall and floor tiles are absorbent to some degree. Just pour a teaspoon of water on to an unsealed tile and see how quickly the water absorbs. The time it takes can vary from between minutes to hours. This is because natural stone, including Limestone and Travertine tiles have small pin-holes and open fissures as part of its natural texture. This texture will tend to accumulate grit as part of the natural wearing process and unless protected the floor will stain. More information on tile absorbency is contained in our useful product guide.

The benefits of sealing

An example of sealed Travertine

Sealing protects natural stone surfaces from spillage and staining

Natural stone wall and floor surfaces such as Limestone and Travertine tiles and paving will benefit from being sealed in a number of ways:

  1. Stain prevention.
  2. Surface enhancement.
  3. Surface protection.

Choosing the correct sealer

Essentially there are two types of sealing product available on the market suitable for natural stone such as Limestone and Travertine:

1.     IMPREGNATING SEALERS

Impregnating sealers are suspended in a liquid carrier which is either spirit or water based. This ensures that the sealer is absorbed into the tile just below the surface, sealing the small pin holes and open fissures. Once absorbed the carrier evaporates, leaving the sealer behind. General characteristics of impregnating sealers are that they give a natural matt or colour enhanced finish and are micro porous. Meaning they are breathable, moisture repellent and resistant to staining. Generally impregnating sealers are effective for interior and exterior use, including use in wet areas such as swimming pools and wet rooms.

 2.     SURFACE SEALERS

Surface sealers in general tend to be water based and will give an alternative type of protection to the surface of natural stone such as Limestone and Travertine. Depending upon the circumstances they can be used on their own or with an impregnating sealer. It is practical to seal both Travertine and Limestone with either an impregnating or surface sealer, or sometimes both. There are a number of factors that will guide your choice. These are:

  1. The type of finished look you want.
  2. The situation the tiles are used in.
  3. The level and type of traffic the surface will carry.
  4. Internal or external use.

Choosing your finish

There are three basic types of finish:

  1. Matt,
  2. Colour Enhanced Matt
  3. Gloss/Satin

Matt and Colour Enhanced Matt are achieved using impregnating sealers and will preserve or enhance the natural appearance of the surface. If a polished or shiny surface finish is desired then a gloss or satin surface sealer should be used.

Consider where your Limestone or Travertine is being used?

Where your stone tiles are used is a factor that can affect your choice of sealer. Impregnating sealers can be used for internal and external use and are ideal for use in wet rooms and swimming pool surrounds. Surface sealers can offer extra protection and are helpful in high traffic areas.

Lets us help you if your are not sure

Deciding which type of sealer you should use is a difficult choice.
This is why we have developed a simple online 3-step identification guide and
offer a free no obligation LTP TECHNICAL HELPLINE, so please give us a call
on +44 (0) 1823 666213 and we will be happy to help you.

Getting the application right

Before applying the impregnating sealer it is vital to make sure that the stone is completely dry. The number of coats required will depend upon the porosity of the stone, a second or third coat of sealer can be needed. Once sealed the tile will resist all staining and provided the stain is wiped away within a reasonable length of time, there will be no evidence of any mark on the surface of the stone.

A common misunderstanding

It is important to remember however that by its nature an impregnating sealer will not protect the surface of a Limestone tile from acid, which can etch the surface. A red wine spillage would be a good example. While an impregnating sealer will give immediate contact protection, if the spill is left for a period of time the acid in the wine will etch into the surface of the Limestone or Travertine. With this in mind, sometimes a secondary surface seal is required to protect the surface of the tile; however this will alter the appearance of the stone by providing a gloss or satin finish.

Maintenance is also important

Once sealed a neutral cleaner should always be used with stone surfaces such as Limestone and Travertine. The wrong cleaner will damage the seal and return the stone to its porous state. Visit or website for more information on everyday maintenance of surfaces. Finally, no sealer lasts forever, however, provided the floor has been correctly sealed and is correctly maintained, it should stay protected for many years.

The LTP Range of products

Recommended product solutions

OPTION 1: MATT

LTP Mattstone and Mattstone H20 are impregnating sealers which provides a natural matt finish with some initial darkening of the surface of the stone, but minimal change to the character of the stone. These sealers can be used outside and in wet areas and should be routinely maintained with LTP Waxwash on floors and LTP Stonewash on walls.

OPTION 2: COLOUR ENHANCED

LTP Colour Intensifier & Stainblock is also an impregnating sealer, but it will also enhance the natural tones and colours of the stone that in most cases leaves a colour enhanced finish. LTP Colour Intensifier & Stainblock can be used outside and in wet areas; it is particularly suitable for showers and should be routinely maintained with LTP Waxwash on floors and LTP Stonewash on walls. LTP Colour Intensifier & Stainblock is an impregnating sealer and will not provide a surface finish.

OPTION 3: GLOSS / SATIN

In cases where a polished or shiny surface finish is required, LTP Ironwax Gloss or LTP Ironwax Satin should be used. LTP Ironwax Gloss will leave the surface of the stone with a higher gloss finish than LTP Ironwax Satin, which as its name suggests is more satin.  These sealers are both hard-wearing; water based surface sealers which are for interior use only. They should not be used in wet areas. Again the wrong maintenance product will damage the seal, so LTP Floorshine is needed, this product not only cleans the floor, but it also adds protection to the sealer.

If you still have further questions about the sealing of natural or artificial stone such
as Limestone and Travertine please contact the LTP TECHNICAL HELPLINE on
+44 (0) 1823 666213 and we will be happy to help you.

Advertisements

8 thoughts on “Sealing and protecting Limestone and Travertine tiles

  1. What can I do if the travertine in floor, complete shower and around tub & wall was not sealed before or after installation? Can I get stains out of shower floor with any of your products?

    • Hi,
      Depending on the level of the staining, as the stone was not sealed and remained porous the Travertine will have absorbed the stain.
      However we would suggest a deep Clean with LTP Grimex at a 1:5 with water dilution first, and if some stains remain try using it neat.
      If you have any other questions you can email us at info@ltp-online.co.uk

      Regards

      Brad

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s