Removing Stubborn Cement & Grout Residues From Porcelain & Ceramic Wall & Floor Tiles

The following is an intensive cleaning guide for removing cement and grout residues from the surface of porcelain and ceramic wall & floor tiles following installation.

Porcelain-Tile-Header-Image

 

FOR USE ON ALL TYPES OF PORCELAIN & CERAMIC WALL & FLOOR TILES

 

1ltr-+-5-Ltr-Grout-stain-reLTP GROUT STAIN REMOVER

A rapid action cleaning agent for removing cement residues, grout stain, efflorescence and other similar deposits.  This product can be used in diluted or concentrated form, to assist removal of stubborn residue.

TECHNICAL FEATURES

  • High performance  .
  • Targets heavy or light films.
  • Walls & floors.
  • Rapid action.
  • Easy to use.
  • Interior & Exterior.
  • Efflorescence remover
DIRECTIONS FOR USE: FLOORS- REMOVING CEMENT AND GROUT RESIDUES MANUAL APPLICATION

GSR-Directions-Manual-Application

Step 1.Dilute solution 1-1 with water.

Step 2. Apply to the surface and leave for 5 minutes.

Step 3. Scrub surfaces and grout joints to release the grout residue.

Step 4. Sponge up or extract released residues and rinse with water.

Step 5. Allow surfaces to dry before allowing traffic.

DIRECTIONS FOR USE:FLOORS-REMOVING CEMENT AND GROUT RESIDUES MACHINE APPLICATION

GSR-Directions-Machine-Application

Step 1.Dilute solution 1-1 with water.

Step 2. Apply to the surface and leave for 5 minutes.

Step 3. Scrub surfaces and grout joints to release the grout residue.

Step 4. Sponge up or extract released residues and rinse with water.

Step 5. Allow surfaces to dry before allowing traffic.

REMOVING EFFLORESCENCE,WATER AND RUST STAINS FROM THE SURFACE OF STEPS AND RISERS.

Removing efflorescence,water,rust from steps and risers

Step 1.Decant solution into spray bottle and label clearly. Surfaces should be as dry as possible before application.

Step 2. Spray the solution onto the surface making sure to work in manageable areas at a time.

Step 3. Agitate immediately using a short haired stiff bristled brush. Repeat application until residues are removed.

Step 4. Rinse well with plenty of cool water. This should be done at least twice.

Step 5. Allow surfaces to dry naturally.

DIRECTION FOR USE- REMOVING CEMENT RESIDUES FROM WALLS……

Removing cement residue from walls

Step 1. Dilute solution 1 :1 in water.

Step 2. Apply to the surface of the tiles using a microfibre cloth.

Step 3. Scrub immediately using a black emulsifying pad.

Step 4. Rinse with water several times.  Change rinsing water frequently.

Step 5. Allow surfaces to dry naturally.  On higher glazes buff with a dry cloth to finish.

 

FURTHER INFORMATION – CLEANING:
After applying the cleaning solution work in teams of two. One operator should agitate the surface using mildly abraisive pad or rotary machine.The other operator should use a sponge and water or wet vac for immediate rinsing & extraction. This will prevent released dirty residues reabsorbing into the surface and greatly reduce the drying time of surfaces. If a scrubbing machine is used, use cool water only within the tank on the machine. Do not put intensive cleaning solution through the machine as this will impair it’s effectiveness.
If applying to walls, steps or risers start on the top and work down. Try to work in manageable areas at a time and make sure to rinse well with plenty of water after each application. Rinsing should be repeated at least 2 times after cleaning. In areas where the staining is deep repeat the process until all of the stains have gone.

USEFUL EQUIPMENT: 4pc pole, pad holder, black emulsifying pad or rotary scrubbing machine with onboard water tank, stiff brush attachment for the machine, wet vac, buckets, sponges, absorbant towels (for spillage control), Plastic film and masking tape for covering and protecting any surfaces not to be cleaned. Avoid prolonged contact with metal surfaces. Rinse immediately. Ensure that any sensitive surfaces not to be cleaned are properly covered and protected before beginning. Ensure that gloves and eye protection and suitable clothing are worn at all times.

 

This information is offered without guarantee. The material should be used so as to take account of the local conditions and the surfaces to be treated. In case of doubt, the product should be tried out in an inconspicuous area

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s