Preparing Surfaces Before Sealing

All to often we see stone surfaces on busy sites that have been sealed, but not properly prepared before the sealing.

Resulting in sealed in boot prints, milling dust from cutting and grinding, and general dirt and grime.

Initial conditioning and cleaning before sealing is an important part of the protection process and ensures that the open pores of the stone are free from contaminants before filling with sealer.

The simple first step is quite commonly missed out and the consequences of this can lead to inadequate sealing resulting in staining and aftercare issues quite soon after installation.

To avoid these issues use LTP Grimex intensive cleaner.

Dilute 1:10 with water.  Wash down surfaces, rinse with water and then leave overnight to dry before sealing.

The result of this simple first step is deeper penetration of sealer, which will provide longer lasting protection………and of course…….no boot prints!

For more information about LTP visit our website.

LTP Grimex

Please note that this information is offered as general guidance only and without guarantee.  Your specific circumstances may need an alternative approach.  In case of doubt, any process should be tried out in an inconspicuous area before general application.

Advertisements

Problem Solving Black Limestone

We are often contacted in particular about black limestone, the appearance of stains and mineral deposits is not uncommon and occurs with most types of limestone, however the appearance on black limestone or darker stone is more prevalent. This is why it is possible to notice some marks appearing even before sealing. As a naturally occurring chemical reaction it is often difficult to avoid. So this blog is all about some of the different things that can happen, what you can do to prevent it or what you can do to resolve the issues as best you can.

Mineral Stains

Mineral deposit stains on black limstone

Mineral stains are sometimes caused when rain water trickles through sand-cement mortar screeds, toppings and bedding under limestone paving can become moderately alkaline. As this rainwater evaporates, its alkalinity increases until the solution becomes saturated.
This solution then can travel to the surface within the limestone where it starts to deposit solids such as white and grey encrustations of calcium carbonate also known as lime plumes.
To remove the the mineral salts from the surface wash the surface with a mild solution of acid*. This will help disperse the mineral salt deposits from the surface.
LTP Grout Stain Remover is a product suitable for the task, dilute 1 part LTP Grout Stain remover in 4 parts warm water and apply to the surface of the stone. Agitate using an emulsifying pad or similar abrasive pad and then rinse thoroughly with plenty of clean water. Repeat process if necessary.
For more information about LTP Grout Stain Remover please see the Technical Data Sheet.

*N.B Grout stain remover may etch the surface and cause the stone to dry lighter.
If the Limestone is either Honed or Polished do not use LTP Grout Stain Remover and instead use LTP Powerstripper.

Mineral deposits causing a banding effect

Halo Stains & Bands Of Mineral Deposits.

This is caused by trace amounts of sodium and potassium oxides within the Limestone which can also be activated by rain water. Even where rain is slightly acidic, the solutions of these salts in rainwater will gradually become alkaline. Surface wetting and evaporation can produce recurrent patches and bands of dampness known as accumulation zones ( rainwater pooling on the surface where it cannot run off).

Evaporation concentrates the alkaline solutions until they become saturated at the  outer limits or edge of accumulation zones. Further evaporation then causes precipitation, crystallisation and immobilisation of the salt at the surface and in pores immediately below the surface. The resulting bands of distinct pigmentation are halo stains as seen in the image above of Limestone.

Grout & Adhesive Stains.

img_0122

Adhesive Stains On Limestone

Grout and adhesive stains like this appear often, if the stone has been sealed beforehand then the process of removing the residues is easier.
After grouting most of the residues should be taken off with water before it fully dries on the surface. For the removal of most grout residues on Limestone we would recommend using LTP Powerstripper. However on more severe cases as shown in the picture above, using a mild solution of LTP Grout Stain Remover may be more effective.
Grout Stain Remover is an acid based cleaner and will etch any acid sensitive surfaces (Limestone, marble, some sandstones, chrome etc).
We would always recommend to test on a small inconspicuous area first.
LTP Grout Stain Remover Tech Data Sheet.

General Dirt & Grime

If your limestone has been outside for a couple of years, it may have seen better days.
General dirt and grime can be easily removed with LTP Grimex.
Dilute in a bucket of water as per instructions on the back of the bottle, then apply and leave for 10 minutes. Give it a scrub with a deck brush or an emulsifying pad and then rinse with plenty of clean water.
After cleaning allow to dry for 24 hours and then the stone will be ready for resealing.

Protect your Limestone with the correct sealing product.

Sealers used to enhance the appearance and help prevent limestone pavers staining from organic matter outside need to be breathable. LTP Mattstone H20 & LTP Stone Oil are examples of breathable sealers suitable for external use. As well as protecting the stone from staining, breathable sealers will allow the microscopic transition of moisture assisting any trapped moisture to escape through the stone from the mortar and sub surfaces. However, moisture permeating through the stone and sealer to the surface can still dry to leave a calciferous deposit.

Once the stone is thoroughly dry and mineral salt deposits are greatly reduced, general dirt and grime has been cleaned off, reseal the stone with an appropriate limestone sealer. LTP Mattstone H20 is highly effective natural stone sealing solution and is suitable for exterior use. However many of our customers have used LTP Stone Oil after acid washing their stone as it helps to re-enhance and deepen the colour.

Apply LTP Stone Oil to the surface of the stone using a paint brush. Allow it to absorb into the stone and then remove any visible excess from the surface after 45 minutes using an absorbent dry towel. The aim is to completely saturate the stone with as many coats of the sealer as necessary, but do not allow the sealer to dry and leave a film on the surface. Do not apply in direct sunlight.
For more information on how to apply please see the Technical Data Sheet.

LTP Mattstone H20 is applied to the surface with a paint brush, allow to absorb for 15 minutes and then apply a second coat. Remove any visible excess on the surface after 45 minutes.
For more information on how to apply please see the Technical Data Sheet.

 

Please note that this information is offered as general guidance only and without guarantee. Your specific circumstances may need an alternative approach. In case of doubt, any process should be tried out in an inconspicous area before general application. 

Sealing Stone Outside.

Limestone, Sandstone, Travertine, Marble, Slate, Granite, concrete:
Regardless of what type of flooring you choose, the likelihood is it will require some form of sealing.

This is because natural stone is porous, and therefore if left unsealed, any moisture will be soaked up by the stone making it very difficult to remove, and potentially leaving the surface permanently stained (sometimes even fallen leaves can cause stains).

The best way to prevent all this is to seal the stone.

When you seal a stone, you are essentially filling any voids or pores of the stone with the sealer. This prevents any further liquid to absorb in to the tile, as demonstrated here with this close up shot of a water droplet on a tile sealed with LTP Mattstone.

When sealing natural stone outside it is important to use a breathable impregnating sealer, this will allow the transition of moisture from underneath.
Examples include LTP Mattstone H20 & LTP External Stone Sealer both are water based breathable sealers and ideal for use outside.

It is important to note that all stones located outdoors are susceptible to a condition known as efflorescence.
This blooming is caused by water moving through the substrate of a material and carrying minerals and salts found in the mortar bed, grout, soil or the stone itself.
We have a blog here all about efflorescence.

Its also very important when laying Natural stone to make sure that its fixed on a full bed of adhesive and not spot fixed.
The end result could look like this if its spot fixed.
Spot fixing issue Sandstone

If this has already happened to your patio, we have a blog here.

When sealing different natural stones, what will vary the most will be how many coats the stone will need before it is fully sealed.
Each stone exhibits different levels of porosity. A tumbled Limestone may have a higher porosity level than a Honed and filled Limestone.

Sealing natural stone with Mattstone H20

Shake bottle before use.

Test the porosity of your stone with water and a teaspoon, using the LTP porosity test.

Once surfaces are clean and dry, apply the product to the surface evenly using a sealant applicator pad, brush or soft cloth.

When sealing its important not to over apply the sealer and redistribute excess, avoid letting the sealer pool on the surface, as this can cause white marks to appear on the stone when it dries.
On highly absorbent surfaces apply several coats wet-in-wet.
After 15 minutes, remove any excess sealer with an absorbent cloth. Do not allow residues to dry on the surface.
Do not walk on the surface for 3 hours.

Sealing natural stone with External stone sealer.
Apply evenly to the surface using a foam roller or paint brush. On more absorbent surfaces apply further coats at hourly intervals until the surface is completely saturated. Remove any residual sealer if still visible after one hour.

Cleaning Tiles Outside

Before you start sealing your stone it is important to make sure your stone is clean and dry, other wise you will just seal in dirt and grime.

Old layers of sealer, dirt residues and light deposits of organic matter and algae must be removed from the surface and pores of the stone.

This can be done by either using LTP Grimex which is a intensive cleaner or LTP Mouldex Paving Cleaner.

To Clean with LTP Grimex, dilute 1:3 with water, apply to the surface with a sponge or water brush and leave to sit on the surface of the tiles for as long as it takes for the dirt to release. (5-30 minutes depending upon the level of dirt). If areas look as if they are drying out just add a little more solution to keep the area wet.

Agitate the surface with a stiff deck brush after approx 10 minutes (scrubber machines can be used).

Continue to scrub while adding clean water. Remove residues from the surface with water or scrubber machine.

Rinse thoroughly with clean fresh water to remove all remaining residues. Use a power washer if necessary.

Allow the surface at least 24 hours to dry before sealing.

To clean with LTP Mouldex Paving Cleaner, Shake well before use.
Surfaces to be treated should be completely dry before application.
Pour solution undiluted directly onto the pavers and spread out evenly using a sponge or paint brush, Garden sprayers can also be used and leave for a minimum of 1 hour.

Apply a little water and agitate with a stiff Deck brush or emulsifying pad to release the dirt and grime, and then rinse thoroughly using a hose or jet wash.
Some stubborn stains and black spot may require a longer treatment, in which case apply and leave on surfaces overnight. If some black spot remains after treatment, It should fade and disappear after a few days following the treatment. If not: re-apply. Keep pets off at all times during treatment. In case of contact with metals, fabrics and painted surfaces rinse with water immediately. Do not use on warm surfaces. Do not apply if rain is imminent. Avoid contact with ponds & plant life: if contact is made rinse well with plenty of water.

General Maintenance.
Weekly or daily depending on conditions, use a hose and a brush to remove any debris that may be lying on the stone.
Then annually if required use LTP Grimex, this will remove surface dirt and grime, possibly every 6-12 months depending on condition.
Dilute Grimex 1:3 parts water and apply the solution on to the surface and agitate.
Leave for 10 minutes before agitating again and then rinse with water.
Allow 24 hours to dry and then if necessary re-apply a light coat of sealer.

PLEASE NOTE: Always follow the detailed instructions on the product labels. Protect stone surfaces from contact with acidic substances. Do not use abrasive materials on honed or polished stones. Avoid using normal detergents or strong bleach cleaners on sealed surfaces as they will gradually remove the protective seal.

Please note that this information is offered as general guidance only and without guarantee. Your specific circumstances may need an alternative approach. In case of doubt, any process should be tried out in an inconspicuous area before general application.

 

How do I clean my external paving?

Featured

Patio’s can give that refined and uniform look to a garden area, a clean cut from grass to stone, and when newly laid they look fantastic.

olive-limestone

If you had them laid before the winter months however they probably won’t look the same now as they once did. With the amount of rain that we have had over the last few months, the probability is that you will have some form of green growth on the tiles.

This green growth is a mix of Algae, moss and lichen which builds up on the tiles, normally more common in areas of higher rainfall, as this is the perfect place for algae to grow, high rainfall and with areas for the algae to cling to.

However this isn’t the end of your patio, as this can be easily fixed with the correct tools.

Cleaning Patios With LTP Mouldex

Firstly you will want to brush the stone with a stiff bristle deck brush to remove any leaves, dirt or debris from the surface of the stone.

Making sure the area is now free of loose debris, pour LTP Mouldex direct on to the stone and spread out over the area with a brush or sponge. (Garden sprayers can be used)

Black limestone with LTP mouldex applied on it with a sponge.

Leave for a minimum of one hour, then add a little water and agitate with a emulsifying pad or stiff deck brush to help loosen algae, dirt and grime.

After a minimum of 1 hour, agitate with emulsifying pad.

After a minimum of 1 hour, agitate with emulsifying pad.

Rinse thoroughly with water. Garden hoses and jet washes can be used. Be careful though as jet washes force water at the surface at high pressures and can cause damage to some stones.
Some stubborn stains and black spot will require longer treatment, in which case apply and leave overnight.

Rinse well with plenty of water

Rinse well with plenty of water

Once fully dry, (normally 24 hours) we recommend sealing with LTP Mattstone H20, this will prevent moisture and organic molecules from absorbing into the surface.

Black Limestone once cleaned and sealed

Black Limestone once cleaned and sealed

LTP Mouldex is a highly effective HSE registered product which has been developed to Help restore natural stone and paving to its original colour.

Grey Limestone with LTP moudlex.

Grey Limestone with LTP moudlex.

KILLS & REMOVES:

  • Algae
  • Black Spot
  • Mildew
  • Mould
  • Lichen
  • Fungus
  • Pollution
  • Pollen stains

Anti-bacterial action helps prevent re-growth.

Suitable for use on all external stones and concrete paving.

Simple to use….apply and leave….scrub and rinse.

The fast acting formula will restore external paving and help prevent re growth.

Protecting stone surfaces after treatment with LTP Mattstone H20 will further reduce the possibility of black spot and mould spores from returning. It will also help prevent deep staining from falling organic matter and make any future cleaning much easier.

Grey Limestone After cleaning and sealing.

Grey Limestone After cleaning and sealing.

One 5ltr can will treat up to 50 sq.m deepending upon the extent of soiling.

LTP Mouldex 5ltr only £39.54 Inc VAT.  (click here to buy or find your nearest stockist)

2_73_e

For further information on the application of LTP Mouldex watch the video below.

Please note that this information is offered as general guidance only and without guarantee. Your specific circumstances may need an alternative approach. In case of doubt, any process should be tried out in an inconspicuous area before general application.

Has your Natural Stone been damaged by Household Cleaner?

We were contacted recently by a customer whose pet had a little accident on their Stoneworks Tumbled Pietra Limestone and tried to remedy it by spraying CIF Bathroom cleaner on it, the result is shown in the photo below!

Stone damaged by Cif Spray

Stone damaged by Cif Spray-Image supplied by Stone Works Ltd

Our response to help rectify was…………….

LTP Grimex should be used to clean the surface of the stones that have been damaged by the CIF spray. This will help to neutralise the reaction that has caused a change in the character of the stones surface. The Lighter marks will still remain following cleaning, but LTP Grimexshould appear a little darker.

Remember to work on the entire piece of stone and not just the areas that are affected. This should be done in a way that does not allow the cleaning solution to spread over onto neighboring tiles, so whole pieces of stone, but only up to the grout joints.

Apply LTP Grimex diluted 1 : 3 with water and agitate the surface….leave for 10 – 15 minutes….agitate again and then rinse well using a sponge and water.

Leave the stone to dry.

 

Apply LTP Stone Oil to the surface and allow to absorb. Check the surface after 45
LTP-StoneOil5LTin_1L_Grp_Webminutes and then wipe up any excess from the surface. ThisLTP-Mattstone5L,1L_500ml_Grp_Web should be repeated until the colour of the stone has been restored. For extra protection and after a 24 hour curing time for the Oil a coat of LTP Mattstone can be used over the top.

 

LTP-Master500mlSpray_2011_Web

For dealing with spillages quickly when they occur we would suggest LTP Stonewash Spray.
This is a spray and wipe cleaner which will remove spillages without compromising the seal or damaging the surface of the stone.

For daily/weekly mopping use LTP Waxwash. This cleaner is PH Neutral and contains a trace of linseed oil, which makes it ideal for cleaning and embellishing sensitive sealed surfaces. A 1 ltr bottle is enough solution to wash a 20 sq.m LTP-Waxwash1L_Webfloor 40 times.

Hope this helps…

Customers response “Hip hip hooray”

  • It’s worked hooray
    Thank you so much
  • Please thank your guy for his help
    I can’t believe it

Thanks very much again xx

This information is offered without guarantee.  The material should be used so as to take account of the local conditions and the surfaces to be treated.  In case of doubt, the products should be tried out in an inconspicuous area before general application.

Cleaning, Sealing and maintaining stone surfaces

Cleaning, Sealing and Maintaining Stone Surfaces 

Natural stone has been used on floors and walls for centuries. As with all natural materials, it does need a certain level of care.

 

Natural Stone Surfaces – Internal Application

The following instructions are appropriate for Travertine, Limestone, Marble, Sandstone, Terrazzo and some Granite.

STEP ONE: INITIAL CLEANING 

Before sealing natural stone must be thoroughly cleaned to make sure that sealing of the surface can be achieved effectively. This is true of newly installed surfaces, as well as existing, due to the contamination that can occur during fitting. Equipment recommended for this step is a bucket, mop, white emulsifying pad, 4pcs pole, sealant applicator & pad holder, microfibre cloth, scrubber or scrubber dryer machine.Stone_cleaning_and_seal_Pack1

Newly installed surfaces

LTP recommends LTP Grimex as the solution for cleaning newly installed natural stone surfaces before sealing. LTP Grimex removes grease, dirt and grime from the surface ensuring the natural stone surface is best prepared for application of a sealing product.

Cleaning newly installed stone surfaces

  1. Dilute LTP Grimex 1:10 with water.
  2. Apply solution to the surface with a mop or sponge. Under floor heating must be off.
  3. Agitate to release the residual dirt and grime from the surface with a mildly abrasive pad (LTP White emulsifying pad).  Rinse well using a sponge & water.
  4. Do not use acidic cleaners, such as LTP Grout Stain Remover.
  5. Allow the surface to dry (preferably for 24 hours).

Cleaning natural stone with LTP Grimex

Refurbishing used and heavily soiled stone surfaces

  • Before sealing the stone must be thoroughly cleaned. Old layers of sealer, residues from aftercare products and deposits must be removed from the surface and pores of the stone. Film forming layers of sealer should be removed with LTP Solvex before washing with LTP Grimex.
  • Depending upon the levels of dirt, dilute LTP Grimex 1:3 with water. Apply with a sponge or cloth and leave to sit on the surface of the tiles for 5-10 minutes.
  • Agitate the surface with a white emulsifying pad (for polished, smooth or honed surfaces) or scrubbing-brush ( LTP Deck brush) for Rough Cut surfaces and leave for a further 5 minutes (scrubber machines can be used).
  • Continue to scrub while adding clean water. Remove residues from the surface using a cloth or scrubber dryer machine.
  • Rinse thoroughly with clean fresh water to remove all remaining residues.
  • Allow the surface to dry for a minimum of 24 hours before applying the protective seal.
  • For the removal of other types of dirt: Do not use acid based cleaners on limestone or marble. If you are unsure please call our helpline on +44 (0) 01823 666213 for advice.

STEP TWO: PROTECT YOUR NATURAL STONE SURFACE FROM STAINS

To protect stone surfaces and help prevent staining natural stone should be sealed. LTP recommends applying LTP Mattstone for a natural (invisible finish) or LTP Colour Intensifier & Stainblock for an enhanced appearance. LTP Colour Intensifier & Stainblock deepens the colour and enhances the appearance of the stone surface.

Sealing prepared natural stone surfaces

  1. Surfaces must be clean and dry. Ensure under floor heating is off.
  2. Apply the product to the surface evenly using either LTP sealant applicator,a sponge, brush or soft cloth.
  3. Redistribute to remove excess product and avoid pooling on the surface.
  4. Allow to dry. Do not walk on the surface for at least one hour.
  5. Protect from water for 24 hours and do not wash surfaces for at least 3 days.

Sealing natural stone with LTP Mattstone, LTP Mattstone H20 or LTP Colour Intensifier.

  • LTP Mattstone H20, LTP Mattstone and LTP Colour Intensifier will make the surface water and oil repellent.
  • Prevents stains, aids cleaning and simplifies the removal of surface stains.
  • Provides an invisible barrier of protection that will not greatly alter the surface character.
  • There are no health concerns once the product has properly cured.
  • LTP Mattstone H20, LTP Mattstone and LTP Colour Intensifier are micro porous and so can be used on surfaces that have no damp proof course.
  • Suitable for internal and external use.
  • If surfaces are properly maintained we recommend touching up the protective treatment every 3-4 years.

NB. Always test the product on an inconspicuous area. Wet or non absorbent surfaces cannot be treated. LTP Mattstone H20, LTP Mattstone and Colour Intensifier are impregnating sealers which need to fully absorb. Do not allow the product to dry on the surface. Carefully buff with a soft cloth or machine to remove any excess. Remove unabsorbed impregnating sealer, if left to dry on the surface, by rubbing over with a little more sealer. Some stones may be darker after application. Acidic substances, if left on the surface, may damage stone.

STEP THREE: MAINTAINING YOUR NATURAL STONE WALL OR FLOOR

Using the correct maintenance product will increase the life of your floor seal, provide additional protection against staining and make sure your floor looks great. Common household cleaning products often contain harsh substances that can breakdown sealing products applied to stone. For this reason LTP recommends using LTP Waxwash on floors and LTP Stonewash for surfaces.

LTP Waxwash (for floors): Formulated for use on unglazed tiles such as travertine, stone, limestone, slate, terracotta and quarry. Ideal for washing floors sealed with LTP Mattstone H20, LTP Mattstone or LTP Colour Intensifier. Use routinely in place of normal detergent.

LTP Stonewash (for walls): This gentle surface cleaner is formulated for use on limestone, marble, granite, slate and polished porcelain. Will clean without breaking down and removing protective seals.

Regular maintenance on stone floors

  1. Add one cap full of product per litre of water in a bucket.
  2. Wipe surface with the solution. Do not rinse.
  3. Allow to dry. Do not walk on the surface during drying time – 20 minutes.

Maintaining natural stone with LTP Waxwash

A one litre LTP Waxwash will wash a 20 sq.m floor 40 times.

PLEASE NOTE: Always follow the detailed instructions on the product labels. Protect stone surfaces from contact with acidic substances. Do not use abrasive materials on honed or polished stones. Avoid using normal detergents or strong bleach cleaners on sealed surfaces as they will gradually remove the protective seal.
At LTP we believe in helping to provide solutions and this is why we offer
a no obligation LTP TECHNICAL HELPLINE, so please give us a call on
+44 (0) 1823 666213 and we will be happy to help you. 
Visit www.ltp-online.co.uk to purchase from the LTP Range of products or find out more about us.

PROBLEMS WITH STEAM CLEANING LIMESTONE

The simplicity of water-based steam cleaning can be appealing, but repeated use of too much super heated water can lead to risks of residual staining, mobilisation of salts and corrosion of hidden particles of Iron within some limestone surfaces.

 

Mud vein in limestone magnified 120 Microns

Surface of a Limestone magnified by 120 microns

Steam can penetrate the small cracks and fissures on the surface of the limestone.
This does clean the limestone, but will also embed water into the surface.
Repeated cleaning using a steam cleaner can activate salts and weaken the stone over time. This can also lead to spalling or fragmentation of the surface.

Cleaning to expose new fissuresCOMPROMISED SEALER?
Surfaces that have been treated with an impregnating sealers can also be compromised. Steam cleaning does not normally remove the impregnating sealer, however repeated use can expose new fissures and capillaries within the stone. The newly exposed and unsealed surface takes in more dirt and becomes harder to clean, which then requires more frequent cleaning. This increase in cleaning can exacerbate the problem.

 

SURFACE SEALER DAMAGE?Damage to stone surface

Sealers used to finish the surface of stone can also be damaged. Steam is often used to remove paints, wall papers and other
coatings from surfaces. If a film forming
sealer has been used then contact by a
steam cleaner can cause a partial separation of the seal from the surface of the stone causing it to turn white or opaque.

 

                                                                        Rust stains in Limestone after spalling
RUST STAINS ON THE SURFACE?                                  
Rust stains:  These stains are reddish-orange and are caused by the oxidation (rusting) of iron. The source of iron staining is normally from within the stone, as most of the iron on the surface is normally
removed or discarded at the point of fabrication by the quarry. Therefore most Iron remains hidden and within the stone rather than on it; however, water from steam cleaning penetrating through natural fissures in the  stone can activate or accelerate rusting.
CRUMBLING OF THE SURFACE?
Moisture from repeated steam cleaning can in someSpalling Limestone
cases cause spalling or fragmentation of the surface.
The migration of salts from moisture in the limestone can promote crumbling of the surface causing larger fissures and craters to appear. This is more
common in Limestone’s and marbles that contain naturally occurring mud or calcite veins which are more vulnerable to this issue.

 

WHAT TO DO?

COMPROMISED SEALER: Intensively clean the surface of the stone with LTP Grimex. Leave overnight to dry. Re-apply impregnating sealer – LTP Mattstone or LTP Colour Intensifier. For routine aftercare use LTP Waxwash. This is a PH neutral cleaner that will not damage the stone or compromise the seal.

SURFACE SEALER DAMAGE: Remove the Film forming sealer using LTP Grimex or LTP Solvex. Leave overnight to dry. Re-apply the film forming sealer – LTP Ironwax Satin or LTP Ironwax Gloss. For routine aftercare use LTP Floorshine. This gentle cleaner will clean the surface and repair the seal where it has worn from abraision every time the floor is washed.

RUST STAINS ON THE SURFACE: Intensively clean the surface of the stone with LTP Power Stripper. Leave overnight to dry.Re-apply impregnating sealer – LTP Mattstone or LTP Colour Intensifier. For routine aftercare use LTP Waxwash. This is a PH neutral cleaner that will not damage the stone or compromise the seal.

CRUMBLING OF THE SURFACE: Intensively clean the surface of the stone with LTP Grimex. Leave overnight to dry. Use a suitable resin stone filler of the correct colour to fill in the voids. Re- hone the surface of the stone using a twister pad and sponge down with a little water to remove any dust or sediment. Leave to dry. Re-apply impregnating sealer – LTP Mattstone or LTP Colour Intensifier. For routine aftercare use LTP Waxwash. This is a PH neutral cleaner that will not damage the stone or compromise the seal.

This information is offered without guarantee.  The material should be used so as to take account of the local conditions and the surfaces to be treated.  In case of doubt, the product should be tried out in an inconspicuous area.

Natural Stone and Tiles – Common Stains: Water

How to remove Water Stains ­from Natural Stone and Tiles

A water stain mark on natural stone

Natural stone and tiles are an investment that can add real quality to your home or office environment. When staining or marking of a stone surface on a kitchen, bathroom or office floor or work surface occurs, such as water stains; this can create a potentially difficult situation to resolve.

Understand your surface

Ensuring that you know what has caused stains on stone, the material stained and whether the surface is protected can all have a bearing on how you should address the issue. If you are in any doubt it is often more straightforward to seek expert assistance. At LTP we offer FREE technical assistance via our Helpline +44 ( 0) 1823 666213. In most cases, it will be easier to assist you if you are able to supply photographs of the issue and surface. Please send images to info@ltp-online.co.uk with as much information as possible.

Is your stone surface protected?

Natural stone protected with LTP Mattstone

Knowing if your stone surface or tiles has a protective seal applied is important in understanding the best solution to address the issue. Often when a protective seal is in place the method for tackling the problem is much less aggressive and simpler. Essentially this is because the stain is most often only affecting the protective seal.

To protect natural stone and tile surfaces to help prevent staining LTP recommends for following sealing products.  LTP Mattstone or LTP Mattstone H20 for a natural (invisible finish) or LTP Colour Intensifier & Stainblock for an enhanced appearance. LTP Colour Intensifier & Stainblock deepens the colour and enhances the appearance of the stone surface.

Common stains on natural stone and tiles – Water Stains

Water stains can appear on natural stone and tile surfaces such as floors and worktops when water is left to stand, as it dries into the surface it can cause a stain. This is most common with porous stone surfaces such as limestone, flagstones, sandstone and terracotta, but water stains can also affect glazed ceramics, porcelain and polished surfaces such as porcelain, granite and marble.

THE MOST COMMON CAUSES OF WATER STAINS ARE OUTLINED BELOW…

Using the wrong maintenance cleaner can gradually affect the performance of the seal. This after a while allows water to penetrate beyond the seal. In areas of hard water, these water droplets can dry out to leave a lime deposit on the surface. Hard water stains are difficult to remove using normal detergents.

Repeated cleaning of stone surfaces using water and a mild detergent can create a film on the surface.  When we mop and clean our surfaces the water dries off to leave a very slight film of residual detergent. In the months that follow this can create a micron thick film across the surface.  Water droplets can dilute the detergent in the area that they sit on leaving a spot mark.  This all happens on a fairly microscopic level, which is why staining of this nature is sometimes only visible when looking across a surface towards a light source.

The LTP approach to removing water stains

The method that LTP recommends for tackling water stains differs depending upon the surface type.

LIMESTONE, MARBLE, TRAVERTINE AND OTHER ACID SENSITIVE SURFACES

For acid sensitive surfaces, we recommend using LTP Grimex or LTP Power Stripper. Simply wash the area as directed by the label instructions, rinse and allow to dry. Note that if the surface has a protective seal the surface may need re sealing. To make sure that you achieve a uniform finish a wider area may need treatment.

PORCELAIN, TERRACOTTA, SANDSTONE AND OTHER NON ACID SENSITIVE SURFACES

For surfaces that are not acid sensitive, we recommend using LTP Grout Stain Remover. Treat the affected area as directed by the product label, rinse and allow to dry. In some cases you can simply buff the surface to its original shine. Where this is not effective and to help maintenance you may consider applying LTP Glaze Protector.

If the stain persists repeat the treatment, if this is unsuccessful please contact our FREE helpline.

PLEASE NOTE: Always follow the detailed instructions on the product labels. Protect stone surfaces from contact with acidic substances. Do not use abrasive materials on honed or polished stones. Avoid using normal detergents or strong bleach cleaners on sealed surfaces as they will gradually remove the protective seal.

At LTP we believe in helping to offer solutions and this is why we offer a no obligation
LTP TECHNICAL HELPLINE, so please give us a call on +44 (0) 1823 666213 or email info@ltp-online.co.uk and we will be happy to help you.

Visit www.ltp-online.co.uk to buy or find out more about our range of products.

LTP cleaning of natural stone

Cleaning tips for natural stone wall and floor tiles

When is intensive stone or deep cleaning required?

  • As an important stage in the installation process of wall and floor tiles.
  • Where poorly maintained natural stone floor tiles need a top up seal.
  • When restoring natural stone wall or floor tiles.
  • For routine cleaning of unsealed external patios and paved areas.

Why would newly installed wall or floor tiles require intensive cleaning?

Keeping natural stone wall and floor tiles scrupulously clean before and during the fixing process, is vitally important. Intensive cleaning of stone floors and walls before application of the correct protective sealing product will make sure the result does not disappoint. Installing stone flooring and worktops by nature creates grit, dirt and adhesive residues. Ensuring that a vacuum is used (being careful not to scratch the surface) to remove loose dirt from your new stone floor or worktop will not address stains and residue marks. Simply washing stone flooring in water will not be effective in removing ingrained marks or adhesive. Using standard household cleaning products that often contain bleach is likely to damage the surface of your newly installed natural stone floor or wall. You should make sure that the correct cleaning product is used for the natural stone material being installed. Need more information about surfaces? Visit our identify your surface selector.

Selecting the correct intensive cleaning product for your natural stone flooring or wall tiles

LTP has developed a range of four intensive cleaning products that offer intensive cleaning solutions for most commercial and domestic applications. Each of our intensive cleaning products has been designed to address the needs of specific circumstances related to artificial and natural stone. We have solutions for all types of natural and artificial stone flooring, granite countertops and fireplace surrounds. Ensuring you have the correct product for the task by simply contacting our Technical Helpline on +44 (0) 1823 666213.

Removing grout stains1. LTP Grout Stain Remover (1&5 litre containers)

An intensive cleaning solution for removal of cement and grout residues from stone flooring and wall tiles. Extremely effective against mineral salt formations (efflorescence) and the removal of plaster and dust stains. Useful for routine cleaning of unsealed patios and other outside paved areas. LTP Grout Stain Remover may be used on glazed ceramics, quarry tiles, terracotta and some stone. (Do not use on limestone, marble or other acid sensitive surfaces.) Buy LTP Grout Stain Remover

 

 

Cleaning grime from natural stone2. LTP GRIMEX (1&5 litre containers)

The answer to stubborn grime, oil, old layers of wax or acrylic and even rubber sole marks on terracotta and natural stone flooring. Ideal for removing ingrained dirt and grime, both internally and externally. Suitable for use on glazed and unglazed tiles this product is excellent for renovating old quarry tiles, terracotta, slate, stone, marble, stone fireplaces and can be used to clean brick and external paving.
Buy LTP Grimex >>

 

 

Removing oxidised linseed oil3. LTP POWER STRIPPER (1&5 litre containers)

For removing existing layers of sealer from tiles. One of the few intensive cleaning products on the market capable of breaking down oxidised boiled linseed oil and beeswax from the surface of terracotta. Powerful amines, ammonia and alkalinity penetrate and help lift the hardest, heaviest films. Ideal for intensive cleaning of heavily contaminated vitrified quarry tiles, limestone, travertine, sandstone, slate, glazed ceramics and porcelain. Strips most things first time thereby minimising labour costs. Buy LTP Power Stripper >>

Removing tick layers of sealant4. LTP SOLVEX (1&5 litre cans)

A powerful non-caustic stripper that softens most types of solvent based surface sealer, which can then be removed with ease. Suitable for removing most wax, oil, emulsion and polyurethane sealers. Will not discolour or damage natural stone, slate, terracotta or quarry tile surfaces. After washing and rinsing, surfaces are ideal for re-sealing. Buy LTP Solvex >>

Cleaning, Sealing and Maintaining Stone Surfaces

Cleaning, Sealing and Maintaining Stone Surfaces 

Natural stone has been used on floors and walls for centuries. As with all natural materials, it does need a certain level of care.

 

Natural Stone Surfaces – Internal Application

The following instructions are appropriate for Travertine, Limestone, Marble, Sandstone, Terrazzo and some Granite.

Step one: Initial cleaning 

Before sealing natural stone must be thoroughly cleaned to make sure that sealing of the surface can be achieved effectively. This is true of newly installed surfaces, as well as existing, due to the contamination that can occur during fitting. Equipment recommended for this step is a bucket, mop, white emulsifying pad, 4pcs pole, sealant applicator & pad holder, microfibre cloth, scrubber or scrubber dryer machine.Stone_cleaning_and_seal_Pack1

Newly installed surfaces

LTP recommends LTP Grimex as the solution for cleaning newly installed natural stone surfaces before sealing. LTP Grimex removes grease, dirt and grime from the surface ensuring the natural stone surface is best prepared for application of a sealing product.

Cleaning newly installed stone surfaces

  1. Dilute LTP Grimex 1:10 with water.
  2. Apply solution to the surface with a mop or sponge. Under floor heating must be off.
  3. Agitate to release the residual dirt and grime from the surface with a mildly abrasive pad (LTP White emulsifying pad).  Rinse well using a sponge & water.
  4. Do not use acidic cleaners, such as LTP Grout Stain Remover.
  5. Allow the surface to dry (preferably for 24 hours).

Cleaning natural stone with LTP Grimex

Refurbishing used and heavily soiled stone surfaces

  • Before sealing the stone must be thoroughly cleaned. Old layers of sealer, residues from aftercare products and deposits must be removed from the surface and pores of the stone. Film forming layers of sealer should be removed with LTP Solvex before washing with LTP Grimex.
  • Depending upon the levels of dirt, dilute LTP Grimex 1:3 with water. Apply with a sponge or cloth and leave to sit on the surface of the tiles for 5-10 minutes.
  • Agitate the surface with a white emulsifying pad (for polished, smooth or honed surfaces) or scrubbing-brush ( LTP Deck brush) for Rough Cut surfaces and leave for a further 5 minutes (scrubber machines can be used).
  • Continue to scrub while adding clean water. Remove residues from the surface using a cloth or scrubber dryer machine.
  • Rinse thoroughly with clean fresh water to remove all remaining residues.
  • Allow the surface to dry for a minimum of 24 hours before applying the protective seal.
  • For the removal of other types of dirt: Do not use acid based cleaners on limestone or marble. If you are unsure please call our helpline on +44 (0) 01823 666213 for advice.

Step two: Protect your natural stone surface from stains

To protect stone surfaces and help prevent staining natural stone should be sealed. LTP recommends applying LTP Mattstone for a natural (invisible finish) or LTP Colour Intensifier & Stainblock for an enhanced appearance. LTP Colour Intensifier & Stainblock deepens the colour and enhances the appearance of the stone surface.

Sealing prepared natural stone surfaces

  1. Surfaces must be clean and dry. Ensure under floor heating is off.
  2. Apply the product to the surface evenly using either LTP sealant applicator,a sponge, brush or soft cloth.
  3. Redistribute to remove excess product and avoid pooling on the surface.
  4. Allow to dry. Do not walk on the surface for at least one hour.
  5. Protect from water for 24 hours and do not wash surfaces for at least 3 days.

Sealing natural stone with LTP Mattstone, LTP Mattstone H20 or LTP Colour Intensifier.

  • LTP Mattstone H20, LTP Mattstone and LTP Colour Intensifier will make the surface water and oil repellent.
  • Prevents stains, aids cleaning and simplifies the removal of surface stains.
  • Provides an invisible barrier of protection that will not greatly alter the surface character.
  • There are no health concerns once the product has properly cured.
  • LTP Mattstone H20, LTP Mattstone and LTP Colour Intensifier are micro porous and so can be used on surfaces that have no damp proof course.
  • Suitable for internal and external use.
  • If surfaces are properly maintained we recommend touching up the protective treatment every 3-4 years.

NB. Always test the product on an inconspicuous area. Wet or non absorbent surfaces cannot be treated. LTP Mattstone H20, LTP Mattstone and Colour Intensifier are impregnating sealers which need to fully absorb. Do not allow the product to dry on the surface. Carefully buff with a soft cloth or machine to remove any excess. Remove unabsorbed impregnating sealer, if left to dry on the surface, by rubbing over with a little more sealer. Some stones may be darker after application. Acidic substances, if left on the surface, may damage stone.

Step three: Maintaining your natural stone wall or floor

Using the correct maintenance product will increase the life of your floor seal, provide additional protection against staining and make sure your floor looks great. Common household cleaning products often contain harsh substances that can breakdown sealing products applied to stone. For this reason LTP recommends using LTP Waxwash on floors and LTP Stonewash for surfaces.

LTP Waxwash (for floors): Formulated for use on unglazed tiles such as travertine, stone, limestone, slate, terracotta and quarry. Ideal for washing floors sealed with LTP Mattstone H20, LTP Mattstone or LTP Colour Intensifier. Use routinely in place of normal detergent.

LTP Stonewash (for walls): This gentle surface cleaner is formulated for use on limestone, marble, granite, slate and polished porcelain. Will clean without breaking down and removing protective seals.

Regular maintenance on stone floors

  1. Add one cap full of product per litre of water in a bucket.
  2. Wipe surface with the solution. Do not rinse.
  3. Allow to dry. Do not walk on the surface during drying time – 20 minutes.

Maintaining natural stone with LTP Waxwash

A one litre LTP Waxwash will wash a 20 sq.m floor 40 times.

PLEASE NOTE: Always follow the detailed instructions on the product labels. Protect stone surfaces from contact with acidic substances. Do not use abrasive materials on honed or polished stones. Avoid using normal detergents or strong bleach cleaners on sealed surfaces as they will gradually remove the protective seal.
At LTP we believe in helping to provide solutions and this is why we offer
a no obligation LTP TECHNICAL HELPLINE, so please give us a call on
+44 (0) 1823 666213 and we will be happy to help you. 
Visit www.ltp-online.co.uk to purchase from the LTP Range of products or find out more about us.