Sealing Stone Outside

Limestone, Sandstone, Travertine, Marble, Slate, Granite, concrete:
Regardless of what type of flooring you choose, the likelihood is it will require some form of sealing.

This is because natural stone is porous, and therefore if left unsealed, any moisture will be soaked up by the stone making it very difficult to remove, and potentially leaving the surface permanently stained (sometimes even fallen leaves can cause stains).

The best way to prevent all this is to seal the stone.

When you seal a stone, you are essentially filling any voids or pores of the stone with the sealer. This prevents any further liquid to absorb in to the tile, as demonstrated here with this close up shot of a water droplet on a tile sealed with LTP Mattstone.

When sealing natural stone outside it is important to use a breathable impregnating sealer, this will allow the transition of moisture from underneath.
Examples include LTP Mattstone H20 which will leave the stone looking as it does naturally. And LTP External Stone Sealer which will enhance any natural colour in the stone, both of these are water based breathable sealers and will require 24 hours to cure.

It is important to note that all stones located outdoors are susceptible to a condition known as efflorescence.
This blooming is caused by water moving through the substrate of a material and carrying minerals and salts found in the mortar bed, grout, soil or the stone itself.
We have a blog here all about efflorescence.

Its also very important when laying Natural stone to make sure that its fixed on a full bed of adhesive and not spot fixed.
The end result could look like this if its spot fixed.
Spot fixing issue Sandstone

If this has already happened to your patio, we have a blog here.

When sealing different natural stones, what will vary the most will be how many coats the stone will need before it is fully sealed.
Each stone exhibits different levels of porosity. A tumbled Limestone may have a higher porosity level than a Honed and filled Limestone.

Sealing natural stone with Mattstone H20 

Shake bottle before use.

Test the porosity of your stone with water and a teaspoon, using the LTP porosity test.

Once surfaces are clean and dry, apply the product to the surface evenly using a sealant applicator pad, brush or soft cloth.

When sealing its important not to over apply the sealer and redistribute excess, avoid letting the sealer pool on the surface, as this can cause white marks to appear on the stone when it dries.
On highly absorbent surfaces apply several coats wet-in-wet.
After 15 minutes, remove any excess sealer with an absorbent cloth. Do not allow residues to dry on the surface.
Do not walk on the surface for 3 hours and protect from wet conditions for 3 days.

Sealing Stone With LTP External Stone Sealer.

Shake bottle well before use. Apply evenly to the surface using a foam roller or paint brush. On more absorbent surfaces apply further coats at hourly intervals until the surface is completely saturated. Remove any residual sealer if still visible after one hour

Cleaning Tiles Outside

Before you start sealing your stone it is important to make sure your stone is clean and dry, other wise you will just seal in dirt and grime.

Old layers of sealer, dirt residues and light deposits of organic matter and algae must be removed from the surface and pores of the stone.

This can be done by either using LTP Grimex which is a intensive cleaner or LTP Mouldex Paving Cleaner.

To Clean with LTP Grimex, dilute 1:3 with water, apply to the surface with a sponge or water brush and leave to sit on the surface of the tiles for as long as it takes for the dirt to release. (5-30 minutes depending upon the level of dirt). If areas look as if they are drying out just add a little more solution to keep the area wet.

Agitate the surface with a stiff deck brush after approx 10 minutes (scrubber machines can be used).

Continue to scrub while adding clean water. Remove residues from the surface with water or scrubber machine.

Rinse thoroughly with clean fresh water to remove all remaining residues. Use a power washer if necessary.

Allow the surface at least 24 hours to dry before sealing.

To clean with LTP Mouldex Paving Cleaner, Shake well before use.
Surfaces to be treated should be completely dry before application.
Pour solution undiluted directly onto the pavers and spread out evenly using a sponge or paint brush, Garden sprayers can also be used and leave for a minimum of 1 hour.

Apply a little water and agitate with a stiff Deck brush or emulsifying pad to release the dirt and grime, and then rinse thoroughly using a hose or jet wash.
Some stubborn stains and black spot may require a longer treatment, in which case apply and leave on surfaces overnight. If some black spot remains after treatment, It should fade and disappear after a few days following the treatment. If not: re-apply. Keep pets off at all times during treatment. In case of contact with metals, fabrics and painted surfaces rinse with water immediately. Do not use on warm surfaces. Do not apply if rain is imminent. Avoid contact with ponds & plant life: if contact is made rinse well with plenty of water.

General Maintenance.
Weekly or daily depending on conditions, use a hose and a brush to remove any debris that may be lying on the stone.
Then annually if required use LTP Grimex, this will remove surface dirt and grime, possibly every 6-12 months depending on condition.
Dilute Grimex 1:3 parts water and apply the solution on to the surface and agitate.
Leave for 10 minutes before agitating again and then rinse with water.
Allow 24 hours to dry and then if necessary re-apply a light coat of sealer.

PLEASE NOTE: Always follow the detailed instructions on the product labels. Protect stone surfaces from contact with acidic substances. Do not use abrasive materials on honed or polished stones. Avoid using normal detergents or strong bleach cleaners on sealed surfaces as they will gradually remove the protective seal.

Please note that this information is offered as general guidance only and without guarantee. Your specific circumstances may need an alternative approach. In case of doubt, any process should be tried out in an inconspicuous area before general application.

Sealing Stone Outside.

Limestone, Sandstone, Travertine, Marble, Slate, Granite, concrete:
Regardless of what type of flooring you choose, the likelihood is it will require some form of sealing.

This is because natural stone is porous, and therefore if left unsealed, any moisture will be soaked up by the stone making it very difficult to remove, and potentially leaving the surface permanently stained (sometimes even fallen leaves can cause stains).

The best way to prevent all this is to seal the stone.

When you seal a stone, you are essentially filling any voids or pores of the stone with the sealer. This prevents any further liquid to absorb in to the tile, as demonstrated here with this close up shot of a water droplet on a tile sealed with LTP Mattstone.

When sealing natural stone outside it is important to use a breathable impregnating sealer, this will allow the transition of moisture from underneath.
Examples include LTP Mattstone H20 & LTP External Stone Sealer both are water based breathable sealers and ideal for use outside.

It is important to note that all stones located outdoors are susceptible to a condition known as efflorescence.
This blooming is caused by water moving through the substrate of a material and carrying minerals and salts found in the mortar bed, grout, soil or the stone itself.
We have a blog here all about efflorescence.

Its also very important when laying Natural stone to make sure that its fixed on a full bed of adhesive and not spot fixed.
The end result could look like this if its spot fixed.
Spot fixing issue Sandstone

If this has already happened to your patio, we have a blog here.

When sealing different natural stones, what will vary the most will be how many coats the stone will need before it is fully sealed.
Each stone exhibits different levels of porosity. A tumbled Limestone may have a higher porosity level than a Honed and filled Limestone.

Sealing natural stone with Mattstone H20

Shake bottle before use.

Test the porosity of your stone with water and a teaspoon, using the LTP porosity test.

Once surfaces are clean and dry, apply the product to the surface evenly using a sealant applicator pad, brush or soft cloth.

When sealing its important not to over apply the sealer and redistribute excess, avoid letting the sealer pool on the surface, as this can cause white marks to appear on the stone when it dries.
On highly absorbent surfaces apply several coats wet-in-wet.
After 15 minutes, remove any excess sealer with an absorbent cloth. Do not allow residues to dry on the surface.
Do not walk on the surface for 3 hours.

Sealing natural stone with External stone sealer.
Apply evenly to the surface using a foam roller or paint brush. On more absorbent surfaces apply further coats at hourly intervals until the surface is completely saturated. Remove any residual sealer if still visible after one hour.

Cleaning Tiles Outside

Before you start sealing your stone it is important to make sure your stone is clean and dry, other wise you will just seal in dirt and grime.

Old layers of sealer, dirt residues and light deposits of organic matter and algae must be removed from the surface and pores of the stone.

This can be done by either using LTP Grimex which is a intensive cleaner or LTP Mouldex Paving Cleaner.

To Clean with LTP Grimex, dilute 1:3 with water, apply to the surface with a sponge or water brush and leave to sit on the surface of the tiles for as long as it takes for the dirt to release. (5-30 minutes depending upon the level of dirt). If areas look as if they are drying out just add a little more solution to keep the area wet.

Agitate the surface with a stiff deck brush after approx 10 minutes (scrubber machines can be used).

Continue to scrub while adding clean water. Remove residues from the surface with water or scrubber machine.

Rinse thoroughly with clean fresh water to remove all remaining residues. Use a power washer if necessary.

Allow the surface at least 24 hours to dry before sealing.

To clean with LTP Mouldex Paving Cleaner, Shake well before use.
Surfaces to be treated should be completely dry before application.
Pour solution undiluted directly onto the pavers and spread out evenly using a sponge or paint brush, Garden sprayers can also be used and leave for a minimum of 1 hour.

Apply a little water and agitate with a stiff Deck brush or emulsifying pad to release the dirt and grime, and then rinse thoroughly using a hose or jet wash.
Some stubborn stains and black spot may require a longer treatment, in which case apply and leave on surfaces overnight. If some black spot remains after treatment, It should fade and disappear after a few days following the treatment. If not: re-apply. Keep pets off at all times during treatment. In case of contact with metals, fabrics and painted surfaces rinse with water immediately. Do not use on warm surfaces. Do not apply if rain is imminent. Avoid contact with ponds & plant life: if contact is made rinse well with plenty of water.

General Maintenance.
Weekly or daily depending on conditions, use a hose and a brush to remove any debris that may be lying on the stone.
Then annually if required use LTP Grimex, this will remove surface dirt and grime, possibly every 6-12 months depending on condition.
Dilute Grimex 1:3 parts water and apply the solution on to the surface and agitate.
Leave for 10 minutes before agitating again and then rinse with water.
Allow 24 hours to dry and then if necessary re-apply a light coat of sealer.

PLEASE NOTE: Always follow the detailed instructions on the product labels. Protect stone surfaces from contact with acidic substances. Do not use abrasive materials on honed or polished stones. Avoid using normal detergents or strong bleach cleaners on sealed surfaces as they will gradually remove the protective seal.

Please note that this information is offered as general guidance only and without guarantee. Your specific circumstances may need an alternative approach. In case of doubt, any process should be tried out in an inconspicuous area before general application.

 

PROBLEMS WITH STEAM CLEANING LIMESTONE

The simplicity of water-based steam cleaning can be appealing, but repeated use of too much super heated water can lead to risks of residual staining, mobilisation of salts and corrosion of hidden particles of Iron within some limestone surfaces.

 

Mud vein in limestone magnified 120 Microns

Surface of a Limestone magnified by 120 microns

Steam can penetrate the small cracks and fissures on the surface of the limestone.
This does clean the limestone, but will also embed water into the surface.
Repeated cleaning using a steam cleaner can activate salts and weaken the stone over time. This can also lead to spalling or fragmentation of the surface.

Cleaning to expose new fissuresCOMPROMISED SEALER?
Surfaces that have been treated with an impregnating sealers can also be compromised. Steam cleaning does not normally remove the impregnating sealer, however repeated use can expose new fissures and capillaries within the stone. The newly exposed and unsealed surface takes in more dirt and becomes harder to clean, which then requires more frequent cleaning. This increase in cleaning can exacerbate the problem.

 

SURFACE SEALER DAMAGE?Damage to stone surface

Sealers used to finish the surface of stone can also be damaged. Steam is often used to remove paints, wall papers and other
coatings from surfaces. If a film forming
sealer has been used then contact by a
steam cleaner can cause a partial separation of the seal from the surface of the stone causing it to turn white or opaque.

 

                                                                        Rust stains in Limestone after spalling
RUST STAINS ON THE SURFACE?                                  
Rust stains:  These stains are reddish-orange and are caused by the oxidation (rusting) of iron. The source of iron staining is normally from within the stone, as most of the iron on the surface is normally
removed or discarded at the point of fabrication by the quarry. Therefore most Iron remains hidden and within the stone rather than on it; however, water from steam cleaning penetrating through natural fissures in the  stone can activate or accelerate rusting.
CRUMBLING OF THE SURFACE?
Moisture from repeated steam cleaning can in someSpalling Limestone
cases cause spalling or fragmentation of the surface.
The migration of salts from moisture in the limestone can promote crumbling of the surface causing larger fissures and craters to appear. This is more
common in Limestone’s and marbles that contain naturally occurring mud or calcite veins which are more vulnerable to this issue.

 

WHAT TO DO?

COMPROMISED SEALER: Intensively clean the surface of the stone with LTP Grimex. Leave overnight to dry. Re-apply impregnating sealer – LTP Mattstone or LTP Colour Intensifier. For routine aftercare use LTP Waxwash. This is a PH neutral cleaner that will not damage the stone or compromise the seal.

SURFACE SEALER DAMAGE: Remove the Film forming sealer using LTP Grimex or LTP Solvex. Leave overnight to dry. Re-apply the film forming sealer – LTP Ironwax Satin or LTP Ironwax Gloss. For routine aftercare use LTP Floorshine. This gentle cleaner will clean the surface and repair the seal where it has worn from abraision every time the floor is washed.

RUST STAINS ON THE SURFACE: Intensively clean the surface of the stone with LTP Power Stripper. Leave overnight to dry.Re-apply impregnating sealer – LTP Mattstone or LTP Colour Intensifier. For routine aftercare use LTP Waxwash. This is a PH neutral cleaner that will not damage the stone or compromise the seal.

CRUMBLING OF THE SURFACE: Intensively clean the surface of the stone with LTP Grimex. Leave overnight to dry. Use a suitable resin stone filler of the correct colour to fill in the voids. Re- hone the surface of the stone using a twister pad and sponge down with a little water to remove any dust or sediment. Leave to dry. Re-apply impregnating sealer – LTP Mattstone or LTP Colour Intensifier. For routine aftercare use LTP Waxwash. This is a PH neutral cleaner that will not damage the stone or compromise the seal.

This information is offered without guarantee.  The material should be used so as to take account of the local conditions and the surfaces to be treated.  In case of doubt, the product should be tried out in an inconspicuous area.

Natural Stone and Tiles – Common Stains: Water

How to remove Water Stains ­from Natural Stone and Tiles

A water stain mark on natural stone

Natural stone and tiles are an investment that can add real quality to your home or office environment. When staining or marking of a stone surface on a kitchen, bathroom or office floor or work surface occurs, such as water stains; this can create a potentially difficult situation to resolve.

Understand your surface

Ensuring that you know what has caused stains on stone, the material stained and whether the surface is protected can all have a bearing on how you should address the issue. If you are in any doubt it is often more straightforward to seek expert assistance. At LTP we offer FREE technical assistance via our Helpline +44 ( 0) 1823 666213. In most cases, it will be easier to assist you if you are able to supply photographs of the issue and surface. Please send images to info@ltp-online.co.uk with as much information as possible.

Is your stone surface protected?

Natural stone protected with LTP Mattstone

Knowing if your stone surface or tiles has a protective seal applied is important in understanding the best solution to address the issue. Often when a protective seal is in place the method for tackling the problem is much less aggressive and simpler. Essentially this is because the stain is most often only affecting the protective seal.

To protect natural stone and tile surfaces to help prevent staining LTP recommends for following sealing products.  LTP Mattstone or LTP Mattstone H20 for a natural (invisible finish) or LTP Colour Intensifier & Stainblock for an enhanced appearance. LTP Colour Intensifier & Stainblock deepens the colour and enhances the appearance of the stone surface.

Common stains on natural stone and tiles – Water Stains

Water stains can appear on natural stone and tile surfaces such as floors and worktops when water is left to stand, as it dries into the surface it can cause a stain. This is most common with porous stone surfaces such as limestone, flagstones, sandstone and terracotta, but water stains can also affect glazed ceramics, porcelain and polished surfaces such as porcelain, granite and marble.

THE MOST COMMON CAUSES OF WATER STAINS ARE OUTLINED BELOW…

Using the wrong maintenance cleaner can gradually affect the performance of the seal. This after a while allows water to penetrate beyond the seal. In areas of hard water, these water droplets can dry out to leave a lime deposit on the surface. Hard water stains are difficult to remove using normal detergents.

Repeated cleaning of stone surfaces using water and a mild detergent can create a film on the surface.  When we mop and clean our surfaces the water dries off to leave a very slight film of residual detergent. In the months that follow this can create a micron thick film across the surface.  Water droplets can dilute the detergent in the area that they sit on leaving a spot mark.  This all happens on a fairly microscopic level, which is why staining of this nature is sometimes only visible when looking across a surface towards a light source.

The LTP approach to removing water stains

The method that LTP recommends for tackling water stains differs depending upon the surface type.

LIMESTONE, MARBLE, TRAVERTINE AND OTHER ACID SENSITIVE SURFACES

For acid sensitive surfaces, we recommend using LTP Grimex or LTP Power Stripper. Simply wash the area as directed by the label instructions, rinse and allow to dry. Note that if the surface has a protective seal the surface may need re sealing. To make sure that you achieve a uniform finish a wider area may need treatment.

PORCELAIN, TERRACOTTA, SANDSTONE AND OTHER NON ACID SENSITIVE SURFACES

For surfaces that are not acid sensitive, we recommend using LTP Grout Stain Remover. Treat the affected area as directed by the product label, rinse and allow to dry. In some cases you can simply buff the surface to its original shine. Where this is not effective and to help maintenance you may consider applying LTP Glaze Protector.

If the stain persists repeat the treatment, if this is unsuccessful please contact our FREE helpline.

PLEASE NOTE: Always follow the detailed instructions on the product labels. Protect stone surfaces from contact with acidic substances. Do not use abrasive materials on honed or polished stones. Avoid using normal detergents or strong bleach cleaners on sealed surfaces as they will gradually remove the protective seal.

At LTP we believe in helping to offer solutions and this is why we offer a no obligation
LTP TECHNICAL HELPLINE, so please give us a call on +44 (0) 1823 666213 or email info@ltp-online.co.uk and we will be happy to help you.

Visit www.ltp-online.co.uk to buy or find out more about our range of products.

LTP cleaning of natural stone

Cleaning tips for natural stone wall and floor tiles

When is intensive stone or deep cleaning required?

  • As an important stage in the installation process of wall and floor tiles.
  • Where poorly maintained natural stone floor tiles need a top up seal.
  • When restoring natural stone wall or floor tiles.
  • For routine cleaning of unsealed external patios and paved areas.

Why would newly installed wall or floor tiles require intensive cleaning?

Keeping natural stone wall and floor tiles scrupulously clean before and during the fixing process, is vitally important. Intensive cleaning of stone floors and walls before application of the correct protective sealing product will make sure the result does not disappoint. Installing stone flooring and worktops by nature creates grit, dirt and adhesive residues. Ensuring that a vacuum is used (being careful not to scratch the surface) to remove loose dirt from your new stone floor or worktop will not address stains and residue marks. Simply washing stone flooring in water will not be effective in removing ingrained marks or adhesive. Using standard household cleaning products that often contain bleach is likely to damage the surface of your newly installed natural stone floor or wall. You should make sure that the correct cleaning product is used for the natural stone material being installed. Need more information about surfaces? Visit our identify your surface selector.

Selecting the correct intensive cleaning product for your natural stone flooring or wall tiles

LTP has developed a range of four intensive cleaning products that offer intensive cleaning solutions for most commercial and domestic applications. Each of our intensive cleaning products has been designed to address the needs of specific circumstances related to artificial and natural stone. We have solutions for all types of natural and artificial stone flooring, granite countertops and fireplace surrounds. Ensuring you have the correct product for the task by simply contacting our Technical Helpline on +44 (0) 1823 666213.

Removing grout stains1. LTP Grout Stain Remover (1&5 litre containers)

An intensive cleaning solution for removal of cement and grout residues from stone flooring and wall tiles. Extremely effective against mineral salt formations (efflorescence) and the removal of plaster and dust stains. Useful for routine cleaning of unsealed patios and other outside paved areas. LTP Grout Stain Remover may be used on glazed ceramics, quarry tiles, terracotta and some stone. (Do not use on limestone, marble or other acid sensitive surfaces.) Buy LTP Grout Stain Remover

 

 

Cleaning grime from natural stone2. LTP GRIMEX (1&5 litre containers)

The answer to stubborn grime, oil, old layers of wax or acrylic and even rubber sole marks on terracotta and natural stone flooring. Ideal for removing ingrained dirt and grime, both internally and externally. Suitable for use on glazed and unglazed tiles this product is excellent for renovating old quarry tiles, terracotta, slate, stone, marble, stone fireplaces and can be used to clean brick and external paving.
Buy LTP Grimex >>

 

 

Removing oxidised linseed oil3. LTP POWER STRIPPER (1&5 litre containers)

For removing existing layers of sealer from tiles. One of the few intensive cleaning products on the market capable of breaking down oxidised boiled linseed oil and beeswax from the surface of terracotta. Powerful amines, ammonia and alkalinity penetrate and help lift the hardest, heaviest films. Ideal for intensive cleaning of heavily contaminated vitrified quarry tiles, limestone, travertine, sandstone, slate, glazed ceramics and porcelain. Strips most things first time thereby minimising labour costs. Buy LTP Power Stripper >>

Removing tick layers of sealant4. LTP SOLVEX (1&5 litre cans)

A powerful non-caustic stripper that softens most types of solvent based surface sealer, which can then be removed with ease. Suitable for removing most wax, oil, emulsion and polyurethane sealers. Will not discolour or damage natural stone, slate, terracotta or quarry tile surfaces. After washing and rinsing, surfaces are ideal for re-sealing. Buy LTP Solvex >>

Cleaning, Sealing and Maintaining Stone Surfaces

Cleaning, Sealing and Maintaining Stone Surfaces 

Natural stone has been used on floors and walls for centuries. As with all natural materials, it does need a certain level of care.

 

Natural Stone Surfaces – Internal Application

The following instructions are appropriate for Travertine, Limestone, Marble, Sandstone, Terrazzo and some Granite.

Step one: Initial cleaning 

Before sealing natural stone must be thoroughly cleaned to make sure that sealing of the surface can be achieved effectively. This is true of newly installed surfaces, as well as existing, due to the contamination that can occur during fitting. Equipment recommended for this step is a bucket, mop, white emulsifying pad, 4pcs pole, sealant applicator & pad holder, microfibre cloth, scrubber or scrubber dryer machine.Stone_cleaning_and_seal_Pack1

Newly installed surfaces

LTP recommends LTP Grimex as the solution for cleaning newly installed natural stone surfaces before sealing. LTP Grimex removes grease, dirt and grime from the surface ensuring the natural stone surface is best prepared for application of a sealing product.

Cleaning newly installed stone surfaces

  1. Dilute LTP Grimex 1:10 with water.
  2. Apply solution to the surface with a mop or sponge. Under floor heating must be off.
  3. Agitate to release the residual dirt and grime from the surface with a mildly abrasive pad (LTP White emulsifying pad).  Rinse well using a sponge & water.
  4. Do not use acidic cleaners, such as LTP Grout Stain Remover.
  5. Allow the surface to dry (preferably for 24 hours).

Cleaning natural stone with LTP Grimex

Refurbishing used and heavily soiled stone surfaces

  • Before sealing the stone must be thoroughly cleaned. Old layers of sealer, residues from aftercare products and deposits must be removed from the surface and pores of the stone. Film forming layers of sealer should be removed with LTP Solvex before washing with LTP Grimex.
  • Depending upon the levels of dirt, dilute LTP Grimex 1:3 with water. Apply with a sponge or cloth and leave to sit on the surface of the tiles for 5-10 minutes.
  • Agitate the surface with a white emulsifying pad (for polished, smooth or honed surfaces) or scrubbing-brush ( LTP Deck brush) for Rough Cut surfaces and leave for a further 5 minutes (scrubber machines can be used).
  • Continue to scrub while adding clean water. Remove residues from the surface using a cloth or scrubber dryer machine.
  • Rinse thoroughly with clean fresh water to remove all remaining residues.
  • Allow the surface to dry for a minimum of 24 hours before applying the protective seal.
  • For the removal of other types of dirt: Do not use acid based cleaners on limestone or marble. If you are unsure please call our helpline on +44 (0) 01823 666213 for advice.

Step two: Protect your natural stone surface from stains

To protect stone surfaces and help prevent staining natural stone should be sealed. LTP recommends applying LTP Mattstone for a natural (invisible finish) or LTP Colour Intensifier & Stainblock for an enhanced appearance. LTP Colour Intensifier & Stainblock deepens the colour and enhances the appearance of the stone surface.

Sealing prepared natural stone surfaces

  1. Surfaces must be clean and dry. Ensure under floor heating is off.
  2. Apply the product to the surface evenly using either LTP sealant applicator,a sponge, brush or soft cloth.
  3. Redistribute to remove excess product and avoid pooling on the surface.
  4. Allow to dry. Do not walk on the surface for at least one hour.
  5. Protect from water for 24 hours and do not wash surfaces for at least 3 days.

Sealing natural stone with LTP Mattstone, LTP Mattstone H20 or LTP Colour Intensifier.

  • LTP Mattstone H20, LTP Mattstone and LTP Colour Intensifier will make the surface water and oil repellent.
  • Prevents stains, aids cleaning and simplifies the removal of surface stains.
  • Provides an invisible barrier of protection that will not greatly alter the surface character.
  • There are no health concerns once the product has properly cured.
  • LTP Mattstone H20, LTP Mattstone and LTP Colour Intensifier are micro porous and so can be used on surfaces that have no damp proof course.
  • Suitable for internal and external use.
  • If surfaces are properly maintained we recommend touching up the protective treatment every 3-4 years.

NB. Always test the product on an inconspicuous area. Wet or non absorbent surfaces cannot be treated. LTP Mattstone H20, LTP Mattstone and Colour Intensifier are impregnating sealers which need to fully absorb. Do not allow the product to dry on the surface. Carefully buff with a soft cloth or machine to remove any excess. Remove unabsorbed impregnating sealer, if left to dry on the surface, by rubbing over with a little more sealer. Some stones may be darker after application. Acidic substances, if left on the surface, may damage stone.

Step three: Maintaining your natural stone wall or floor

Using the correct maintenance product will increase the life of your floor seal, provide additional protection against staining and make sure your floor looks great. Common household cleaning products often contain harsh substances that can breakdown sealing products applied to stone. For this reason LTP recommends using LTP Waxwash on floors and LTP Stonewash for surfaces.

LTP Waxwash (for floors): Formulated for use on unglazed tiles such as travertine, stone, limestone, slate, terracotta and quarry. Ideal for washing floors sealed with LTP Mattstone H20, LTP Mattstone or LTP Colour Intensifier. Use routinely in place of normal detergent.

LTP Stonewash (for walls): This gentle surface cleaner is formulated for use on limestone, marble, granite, slate and polished porcelain. Will clean without breaking down and removing protective seals.

Regular maintenance on stone floors

  1. Add one cap full of product per litre of water in a bucket.
  2. Wipe surface with the solution. Do not rinse.
  3. Allow to dry. Do not walk on the surface during drying time – 20 minutes.

Maintaining natural stone with LTP Waxwash

A one litre LTP Waxwash will wash a 20 sq.m floor 40 times.

PLEASE NOTE: Always follow the detailed instructions on the product labels. Protect stone surfaces from contact with acidic substances. Do not use abrasive materials on honed or polished stones. Avoid using normal detergents or strong bleach cleaners on sealed surfaces as they will gradually remove the protective seal.
At LTP we believe in helping to provide solutions and this is why we offer
a no obligation LTP TECHNICAL HELPLINE, so please give us a call on
+44 (0) 1823 666213 and we will be happy to help you. 
Visit www.ltp-online.co.uk to purchase from the LTP Range of products or find out more about us.

How to remove staining from Black Limestone before sealing.

Visible stains on Black Limetone

Visible stains on Black Limetone

After quarrying, milling and then packing a black limestone it is possible for residues of moisture and sediment to remain on the surface. If left over a period of months these deposits of mineral and sediment absorb into the pores of the stone. This type of staining can be very difficult to remove using conventional cleaning materials. The following is a guide to help restore the                                                                                     appearance of the stone using a strong                                                                                   cleaner and then sealing to restore and                                                                                   enhance the colour.

DIRECTIONS FOR CLEANING AND SEALING

1. LTP Grout Stain Remover is applied and 2. GSR scrub immediatelythen immediately scrubbed into the surface using a black emulsifying pad. This should be done for 1 – 2 minutes making sure to cover the whole surface of the stone. This cleaner will slightly etch the surface of the stone to release the stains from within.

 

3. Rinse well with plenty of water2. Do not leave the cleaner to dwell on the surface. Rinse with water immediately after scrubbing. Change the rinsing water every 5 M².
After cleaning leave surfaces to dry for 24 hours.

 

4. Leave to dry
3. Once dry, surfaces will appear grey rather than black. The stains should no longer be visible. The surface of the stone has been conditioned ready for sealing.

 

5. Apply Stoneoil4. Apply a small amount of LTP Stone Oil to the surface of the Limestone and spread out evenly. Leave to absorb into the surface of the stone for 1 hour. Any visible excess after this time work should be worked off using a soft absorbent towel.

6. Spread out evenly

5. The sealer should be left to dry for a minimum of 24 hours with light traffic only.
It will take a further 3 days to reach full hardness, so surfaces should be kept as dry as possible during this time.

INTERIORS
Finishing the stone with a light coat of LTP Mattstone should be considered if the stone is to be used in kitchen areas.

INITIAL CLEANING:                LTP GROUT STAIN REMOVER                   1ltr & 5ltr

This should be done after fixing and before sealing LTP-GroutStainRemover5L&1L_2011_Weband grouting to remove calcium carbonate and mineral deposits including dust and dirt that has accumulated during the production and fixing process. Apply undiluted solution to the surface of the stone and agitate immediately with an emulsifying pad. Rinse thoroughly with a separate pot of clean fresh water. Wipe away the released calcium dirt and grime with a mop or sponge and water and leave to dry for 24 hrs.

TDS – http://www.ltp-online.co.uk/images/tds-Grout_Stain_Remover.pdf

MSDS – http://www.ltp-online.co.uk/images/msds-Grout_stain_remover_clp_GHS.pdf

SEALING:                                      LTP STONEOIL                                        1ltr & 5ltr

Before grouting apply a light coat of LTP Stone Oil, LTP-StoneOil5LTin_1L_Grp_Webcheck that all of the sealer has been
fully absorbed within 1 hour, any excess that remains on the surface after 1 hour should be worked in with a soft cloth or buffing machine. Leave for a further 4 hours or overnight before grouting the joints. Once all residual grout has been removed and the surface and joints are thoroughly dry; apply a final light coat of StoneOil covering the joints as well. Buff to remove any excess within 1 hour and then leave for a minimum of 3 days to fully harden before making excessively wet.

TDS – http://www.ltp-online.co.uk/images/tds-Stone_Oil.pdf
MSDS – http://www.ltp-online.co.uk/images/msds-Stone_oil_clp_GHS.pdf

IMPORTANT NOTES:
When cleaning or sealing vertical surfaces always start at the top and work down.
Provided that the surfaces are correctly sealed and maintained protection should last 3 – 4 years before considering applying a top up coat. Sealing will not prevent wear from abrasion.Used externally sealers will last between 1 & 2 Years before light cleaning and topping up.
After Intensive cleaning to remove any ingrained dirt or other staining and once dry, always test for moisture ingress. If evident cleaned areas should be re-sealed.
When using LTP Grout Stain Remover, gloves should be worn.
For detailed application instructions please see Technical Data Sheets.
This information is offered without guarantee. The material should be used so as to take account of the local conditions and the surfaces to be treated. In case of doubt, the product should be tried out in an inconspicuous area

How To Remove Orange/Pink Stains From The Edges Of Natural Limestone

Tanin and mould stains on Limestone copy

 

DEEP CLEAN UN-SEALED SURFACES TO REMOVE STAINS BEFORE SEALING

 

Limestone tiles are saturated with moisture during fabrication and packed into wooden crates for transport.  They are tightly packed so any retained moisture within the stone can remain for many weeks after packing. Moisture in the stone absorbs into the timber of the crate, which after a while causes tannins from the timber to become drawn into the edge of the stone, where it dries to leave an orange pink deposit. Retained moisture can also encourage the growth of mould spores which also contribute towards the staining affect.

PICTURE 1: SHOWS ORANGE STAINING FROM ALONG THE EDGE OF A PIECE OF WHITE LIMESTONE

Before copy

PICTURE 2: SHOWS APPLICATION OF MOULDEX TO THE EDGE AND SURFACE OF THE STONE

Mouldex application copy

PICTURE 3: SHOWS THE RESULT, PINK & MOULD STAINS HAVE BEEN REMOVED & THE STONE IS CLEAN

After copyBefore, during & After close up copy

STAIN REMOVAL:                         LTP MOULDEX                                                 500ML

Spray Mouldex to the edges and surface of the stone and spread out evenly making sure to cover the whole stone and not just the areas affected by staining. Leave on the surface for 2 – 3 hours. Agitate using a soft (white) emulsifying pad until the solution foams up and rinse well using plenty of water and a sponge. Change rinsing water after every 5 M². Surfaces should be left for a minimum of 24 hrs before sealing.

TDS – http://www.ltp-online.co.uk/images/tds-Mouldex.pdf

 

SEALING:                                        LTP MATTSTONE                                500ML,1&5ltr

Apply LTP Mattstone Sealer evenly to the surface of the stone using a sealant applicator pad. The impregnating sealer should be left for 45 minutes to absorb. Buff well using a soft cloth or machine with white pad to work off any visible excess.  Apply further coats at two hourly intervals using the same method. The object is to fully saturate the marble and terrazzo with sealer without allowing any excess to dry on the surface. The marble will be more absorbent than the terrazzo. Leave for a minimum of 24 hours before allowing traffic.  Treated surfaces will take about 3 days to become fully resistant. So light traffic only and do not wash.

TDS – http://www.ltp-online.co.uk/images/tds-Mattstone.pdf

IMPORTANT NOTES:
For really stubborn stains the stain removal process may need to be repeated.
Provided the surfaces are correctly sealed and maintained protection should last 4 – 5 years before considering applying a top up coat. Sealing will not prevent wear from abrasion. Stone surfaces laid in heavily trafficked areas should be tested for moisture ingress every 12 – 18 months. If moisture absorbs apply more sealer.
After Intensive cleaning to remove any ingrained dirt or other staining and once dry, always test for moisture ingress. If evident cleaned areas should be re-sealed. Maintain sealed surfaces with PH Neutral cleaner LTP Waxwash.
For detailed application instructions please see Technical Data Sheets.
This information is offered without guarantee.  The material should be used so as to take account of the local conditions and the surfaces to be treated.  In case of doubt, the product should be tried out in an inconspicuous area

Porcelain and Ceramic tiled floors look great when just washed

How do I keep that clean shiny look for my tile floor?

Apply LTP Glaze ProtectorOne thing we are told time and time again is that our customers really like the appearance of their floor tiles when they have just been mopped. The question is “Is there anything I can use on my tile floor to make them stay like that?”

The answer is yes…

LTP has a product called LTP Glaze Protector.

RESTORE – REVIVE – RETAIN

Achieving and retaining that perfect looking tile floor is often the goal of our customers. LTP Glaze Protector provides a genuine solution for ceramic, porcelain and vitrified quarry surfaces. Simply follow this 3 step guide to a new looking shine floor.

Restore – Revive – Retain

1. Restore

Bring old tired floors back to life by giving them a really thorough clean with LTP Grimex. This will get the oldest dirtiest floors back to their original condition.

LTP Grimex

Cleaning Porcelain withLTP GrimexHeavy duty grime remover for interior and exterior use. Effective for removing oil, grease, ingrained dirt grime and old wax layers. Important: Test the solution on an inconspicuous area before general application. Any alkalinity remaining on surfaces treated with this product should be completely neutralised. This can be done with a little clean water applied by sponge.

Key facts:

  • Heavy Duty Grime Remover.
  • Removes oil, grease and dirt.
  • Removes old wax layers.
  • Suitable for interior use.

Buy LTP Grimex >>>

2. Revive

LTP Glaze Protector

LTP Glaze Protector gives a just washed lookCreate the ‘just washed’ look to your newly cleaned surfaces by applying LTP Glaze protector. This robust film forming sealer will enhance the appearance of even the dullest floor. It is easy to apply, quick drying and eases maintenance on rougher more textured surfaces. LTP Glaze Protector is quite unique and will give a clean and shiny sheen to ceramic tile floors or porcelain. It is a low maintenance, self shine, film forming sealer for all types of tiled floor including glazed or unglazed ceramic, porcelain, unpolished porcelain and vitrified quarry tile. Once applied this product will help protect and embellish the surface. LTP Glaze Protector delivers a high resistance to wear and helps prevent staining of your tile floor. Using this product will also help with ongoing maintenance and cleaning of your ceramic or porcelain tile floor.  

Key facts:

  • Low maintenance self shine sealer.
  • Highly resistant to wear and stains. 
  • For interior use only.

Buy LTP Glaze Protector >>>

3. Retain

A tile floor treated with LTP Glaze Protector should be maintained with LTP Floorshine to help reinforce protection and make sure your floor remains clean and looking great. 

LTP Floorshine

Buffing PorcelainLTP Floorshine is a highly effective maintenance cleaner for tiled surfaces and is ideal for all types of porcelain, ceramic and vitrified quarry tiles.Maintain the ‘just washed’ look with regular us of LTP Floorshine. In place of your normal detergent, simply put one cap full of Floorshine per litre of water and mop your surfaces. This product will clean your surfaces and repair the seal every time you use it. A one litre container is enough solution to wash a 20 square metre floor 40 times so it is very economical.

Key facts:

  • Cleaner for tiled surfaces.
  • Will help reinforce protection for surface sealers.
  • For interior use only. 

Buy LTP Floorshine >>>

At LTP we believe in helping to provide solutions and this is why we offer a no obligation LTP TECHNICAL HELPLINE, so please give us a call on +44 (0) 1823 666213 and we will be happy to help you. Visit www.ltp-online.co.uk to buy from the LTP Range of products or find out more about us.

Basalt stone – Dealing with white patches

Basalt stone case study

A Basalt tiled floor showing white patches of discolouration.Issues with white patches appearing after sealing Basalt tiles

We were recently contacted by a customer who was having problems with white patches appearing on their newly installed Basalt tiles. This is a common problem, so we thought we should share why and how this issue sometimes occurs. The pictures in this post supplied by a customer show a charcoal grey Basalt tile that has been sealed with a reputable stone tile sealing product.

The customer explained:

“The dark tile is where a colour enhancing tile sealing product was used by the tiler to test to see if it might remove the lighter patches but as you can see this has only enhanced them; the tiled shelf has not had the sealer applied and displays the similar distinct lighter patches; one of the tiles has very distinct striations where it appears the saw marks have not been completely ground out; the floor looks dusty but it is not.”

Basalt floor tiles with white discolouration patches Basalt floor tiles showing white discolouration

How and why discolouration can occur in Basalt stone surfaces and tile installations.

Understanding Basalt stone

In geological terms, basalt is quite a young volcanic stone. When volcanic eruptions take place and volcanic material is formed, excess argon gas can get trapped within lava flows. This argon is held primarily in lattice vacancy defects within the minerals that form to make basalt. These pockets of argon gas are sometimes released when the stone is quarried, cut into blocks, sawn into slabs and then honed on the surface to make it ready for use as a cladding and tiling material. This ensures that Basalt has an extensive capillary make up.

What can cause discolouration and hazing?

Moisture and polymer from adhesive used to complete installations can be drawn up through the natural capillaries within the stone. This can release minerals and salts from within the stone, causing a light bloom or haze from within. In this instance, there is no chemical cure or cleaner that will remove the stains from the stone.

It is also common to see grout floated across the surface (in order to complete grouting between the tiles). This will often fill some of the open capillaries contributing towards a mottled and uneven appearance. In this case, grout on the surface can be removed using a chemical cleaner but grout that has settled within the open pores is likely to be impossible to remove. No amount of scrubbing or cleaning will make any difference. In both cases any additional sealing would only further highlight the marks left by the adhesive and the grout.

Removing the discolouration and hazing

There are two alternative approaches to addressing this issue:

  • For surface grout stains attempt to clean back the surface of the tile with a specialist intensive cleaner and reseal.
  • Remove and replace the tiles.

Intensively clean and reseal

Please note that the following advice should be completed on a small area (single tile) to establish if it will result in a more satisfactory finish:

Clean thoroughly with LTP Grout Stain Remover. This will effectively etch the surface of the stone and should dry to leave it more even in appearance. Note that this treatment will change the texture of the stone making it feel a little rougher. Rinse thoroughly and leave to dry. Re-seal using LTP Mattstone H20 applying as many coats as necessary to achieve saturation. Do not let the solution dry on the surface. Remove any visible excess from the surface within 20 minutes.2.

Remove and replace

Unfortunately, where staining has been caused by moisture drawn up through the stone or grout cannot be removed the only other option would be to remove and replace the tiles.

How to avoid issues when installing Basalt stone

When the new stone is fitted, make sure that the underside of the stone tile is sealed before laying. Use a good quality water-based sealer such as LTP Mattstone H20. After laying and before grouting, seal the surface of the stone with as many coats as necessary to reach saturation point. Before completing the general application of grout, test a small area for grout ingress. Grout ingress is caused when grout material is forced into the surface of the stone during the grouting process and can be difficult to remove. If grout material is absorbed, then a further coat of sealer may be required before proceeding.

Once all residual grout has been removed and surfaces are clean and dry, finish with a further coat of sealer making sure to cover the grout joints as well.

Please note: Always read the product label instructions before using any LTP product and contact our free Technical Helpline on +44 (0) 1823 666213 for further information or assistance if required.

At LTP we believe in helping to provide solutions and this is why we offer a no obligation LTP TECHNICAL HELPLINE, so please give us a call on +44 (0) 1823 666213 or email info@ltp-online.co.uk and we will be happy to help you.

Visit www.ltp-online.co.uk to buy or find out more about our range of products.